Devices You Need to Set Up a New Bathtub
Devices You Need to Set Up a New Bathtub
Blog Article
Presented here in the next paragraph you will find more very good information and facts with regards to Installing A Bathtub.
Setting up a bath tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is also a moderately hard task. If the old tub is easily obtainable, the project can relocate easily; if you have to open up a wall surface to remove the old tub and also place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed job, it is far better to take into consideration employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This write-up will certainly aid you install a new bathtub in your restroom if you have actually currently acquired a brand-new bathtub and don't need to change the arrangement of your previous supply of water pipes.
Your devices as well as product list must consist of the following:
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before moving on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the water supply as well as examine all joints and also new pipework for leakages and also tighten them if necessary. Fill up the bath tub and also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The former kind ought to be linked to the tap ends first, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently offered on the market. It is a good idea to fit the tiles making use of waterproof or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Hopefully you enjoyed our piece on How to Install a Bathtub. Thanks a lot for taking the time to read through our piece of content. Liked our blog posting? Please share it. Let somebody else find it. Thank you for your time invested reading it.
View
Report this page